\n
![\"Screen](\"http:\/\/smelko.com\/site\/wp-content\/uploads\/2013\/02\/Screen-shot-2013-07-25-at-12.04.21-PM.png\")
<\/a>\n<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n The newest complement to Fremont Flasks has already caught on rapidly. It has solved many problems, where weight has become a conscious factor in molding today. It features 1″ flanges with overall lighter construction. We have done this without sacrificing the strength of the flask. All other specifications remain the same to insure continuity.<\/p>\n The Fremont Model A Standard Spreadlock Flasks are constructed of Magnesium Metal. By using this metal, this flask is designed for heavy duty work and is comparable in weight to a medium weight flask constructed from Aluminum. Magnesium metal is particularly adapted to flask construction as it is one-third lighter in weight and at the same time has approximately twice the tensile strength. Standard Specifications The Fremont Model AA Extra Heavy Duty Spreadlock Flasks are constructed of Magnesium or Dowmetal exclusively. This metal is lighter and stronger than Aluminum and is particularly adapted to flask construction. These flasks are designed for all types of heavy duty production jobs and can be furnished with attachments to fit any type of molding machine. Standard Specifications<\/strong><\/p>\n Width: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a010″ to 36″ graduated in even inches <\/p>\n Fremont Super Heavy Duty Flasks for High Pressure Molding Machines. Available in all sizes. All 4\u00b0 taper. 3″ Wide Flanges with 1\/4″ steel facing strips for extra strength. Fremont Standard Rigid Jackets are available in either Cast Iron or Cast Aluminum. Fremont Ribbed or Vented Jackets are particularly designed for use in Steel Foundries. The ribbed construction permits gas to escape more readily. Fremont Jackets are engineered for most automated systems. The same basic high quality jacket Fremont that has been furnishing the foundry industry since 1938 is now specially designed for automated shifting devices. The Flecks-O Jacket is assembled from four castings, so if you have the misfortune to break one of them, you need not to replace the entire jacket. COmpletely machined and drilled replacement castings can be furnished at a nominal cost. These can be installed simply by removing two special studs (part No. 50) Fremont Cast Aluminum bottom boards are a wide range of squeezer sizes. <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p><\/div><\/a><\/p>\n<\/a><\/p>\n<\/a>
\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/a><\/p><\/div>
\nSpreadlock Flask
\nModel 1\/2A<\/h2>\nMagnesium Spreadlock Flask
\nModel A<\/h2>\n
\nOpening corners are operated with hardened forged cams with an aluminum lever. Replaceable live rubber inserts close the corner gaps preventing sand from lodging in the corners.
\nMale and female stops are inserted above and below cams giving added strength to open corners and thus maintain perfect alignment indefinitely.
\nThe standard Model A Fremont Flask is designed for all types of machine production jobs and can also be handled on a bench.
\nOne of the outstanding features of Fremont Flasks is the 1″ Round Groovelock Pin and guide which is standard equipment on our flasks. \u00a0However, Flasks can be furnished with any other type of pin and guide which a customer may prefer. The method we use in attaching the Groovelock Pin in the drag guarantees perfect alignment indefinitely under normal working conditions. The only maintenance on this type of pin and guide is an occasional adjustment of the guide to take up any slack caused by wear.
\nAll Fremont Spreadlock Flasks are jig and fixture drilled and machined. End or side castings are easily replaced. Particular attention is called to the sturdy construction of our tight corners. These corners are assembled by inserting three No.42 dowel sleeves through which 5\/16″ cap screws are inserted.<\/p>\n
\n<\/strong>Width: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a010″ to 24″ graduated in even inches
\nLength: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a012″ to 24″ graduated in even inches
\nCope Depths: \u00a0 \u00a0 \u00a0 \u00a04″ to 6″ graduated in one-half inches
\nDrag Depths: \u00a0 \u00a0 \u00a0 \u00a0 3″ to 6″ graduated in one-half inches
\nPins: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a01″ Round Groovelock with #11 Cope Guides
\n______________11\/16″ Double Round Pins with #8-L Cope Guides
\nPin Centers: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 For 1″ round Groovelock Pins add 3″ to length of Flask
\n______________11\/16″ Double Round Pins can be installed\u00a0on any practical centers
\nFlanges: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 Minimum 3\/8″ thick x 1 3\/8″ wide with top cope flange and bottom \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0______drag \u00a0 \u00a0 \u00a0 \u00a0flange steel forced with \u00a01\/2″ x 1 1\/4″ Cold Rolled Steel
\nSteel Facing: \u00a0 \u00a0 \u00a0 \u00a01\/8″ x 1 1\/4″ steel facing is attached to top of cope and bottom of ______________drag flanges
\nTapers: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 3\u00b0, 4\u00b0 or 5\u00b0 are standard<\/p>\n<\/h2>\n
Extra Heavy Duty Spreadlock Flask
\nModel AA<\/h2>\n
\nFlanges and Ribs are extra heavy to withstand heavy pressures without bowing in the centre.
\nFremont Model AA Extra Heavy Duty Flasks are equipped with one set of No. 40 cams in each open corner with No. 41-A Male and Female Stops above and below the cam. On deeper Copes and Drags, two sets of cams can be installed and if desired these can be connected with a bar and handle for simultaneous operation.<\/p>\n
\nLength: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a016″ to 36″ graduated in even inches (also avail. in fractional inches)
\nCope Depths: \u00a0 \u00a0 \u00a0 \u00a04″ to 8″ graduated in one-half inches
\nDrag Depths: \u00a0 \u00a0 \u00a0 \u00a0 3″ to 8″ graduated in one-half inches
\n_ \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0Model AA Spreadlock Flasks can be furnished up to 84″ lengths.
\n_ \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0Copes and Drags can be furnished in one piece up to 1-” depths.
\n_ \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0Upset frames must be used on any section over 10″ deep
\nPins: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a01″ Round Groovelock (11\/16″ Double Round Pins with #8-L Cope
\n_ \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0Guides can also be furnished)
\nPin Centers: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 For 1″ round Groovelock add 3″ to length of Flask
\n_ \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 11\/16″ Double Round Pins can be installed\u00a0on any practical centers
\nFlanges: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a03\/8″ to 3\/4″ thick x 1 3\/8″ to 2″ wide depending on size of flask
\nSteel Facing: \u00a0 \u00a0 \u00a0 \u00a01\/8″ x 1 1\/4″ steel facing is attached to top of cope and bottom of
\n_ \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 drag flanges
\nTapers: \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 3\u00b0, 4\u00b0 or 5\u00b0 are standard<\/p>\nSuper Heavy Duty Spreadlock Flask
\nModel AAA<\/h2>\n
\nFremont Magnesium Spreadlock Flasks \u00a0are available in a full range of sizes and can be equipped with trunnions for Roto-Lift, Rol-N-Rap and Jolt’n Strip Match Plate Molding Machines.<\/p>\nFremont Standard Rigid Jackets<\/h2>\n
\nAll Fremont Jackets have a bolted corner construction. THese corners are precision machined and drilled on a jig. \u00a0In side surfaces are disc ground. With this construction, replacement castings, machined and drilled ready for installation, can be furnished for broken ends or sides. Jackets otherwise scrapped can be salvaged at a very slight cost, as it is only necessary to remove a few cap screws to install a new side or end casting. Fremont Rigid Jackets can be assembled on either 3\u00b0, 4\u00b0, or 5\u00b0 taper.<\/p>\nFremont Ribbed Type Rigid Jackets<\/h2>\n
\nOtherwise Fremont Ribbed Jackets have the same construction as the standard Jacket and are available in either Cast Iron or Cast Aluminum.
\nWhen ordering Jackets separately be sure to specify the taper, how much of the jacket is to rest above and below the parting line.<\/p>\nJackets for Automated Systems<\/h2>\n
\nFremont jackets outperform other jackets and are field proven in reducing scrap. Jackets are jig drilled and machined for replaceable sides or ends. TIght or loose corners are available to meet your needs.<\/p>\nFremont Flecks-O Jacket<\/h2>\n
\nThe Fremont Flecks-O Jacket will automatically line up with the sides of the molds made in flasks assembled by any of the standard tapers. These Jackets are available in either Cast Iron or Cast Aluminum.
\nWhen ordering Flecks-O Jackets, the only information we require is the length and width of the flask at the parting line, depth of the jacket and how much is to rest below the parting line. Also whether Cast Iron or Aluminum Jackets are desired.<\/p>\nFremont Aluminum Bottom Boards<\/h2>\n
\nFremont Standard bottom boards have 3\/4″ ribs and surface plate. These reinforced ribs provide added strength and rigidity in preventing mold breakage and give extra long life. Vent holes provide free venting of molds.
\nFremont Standard Bottom Boards are also available with an offset flange to act as a peen and also retain mold to board.
\nSpecial Aluminum bottom boards for automated mold machining lines are also available. These high quality bottom boards are tops in the field and made to withstand the rigours of your molding operation.<\/p>\nFremont Flask Part List<\/h2>\n
<\/a><\/div>\n<\/a><\/p><\/div>
\n
\n<\/a><\/a><\/a><\/a><\/a>
\n<\/div> <\/h2>\n
<\/h2>\n
Pins For Fremont Flasks<\/h2>\n
Bushings For Fremont Flasks<\/h2>\n
Parts For Spreadlock Flask Cam Assemblies<\/h2>\n
Replacement Parts for Camlock Corner Assembly<\/h2>\n
![\n<\/a>](\"http:\/\/smelko.com\/site\/wp-content\/uploads\/2013\/02\/freemont-pins.jpg\"){kind=link}